Lake Monitors - Amet Co.,Ltd

HIGH TEMPERATURE FLOW METER

Alex — Fri, 10 Mar 2023 10:10:32 +0000

Lake’s High Temperature Flow Meters enable flow monitoring of barrel heating fluids, thermal transfer fluids such as Syltherm® coolant flows, hydraulic circuits, and sub-circuits. Select from aluminum, brass, or stainless steel design for media compatibility requirements. High temperature flow meters are available for air, water, and oil flow measurement with maximum temperature of 600°F.

MEASURING ACCURACY:

±2.0% of full scale

REPEATABILITY:

±1% of full scale

FLOW MEASURING RANGE:

0.1-150 GPM (0.4-560 LPM)

MAXIMUM OPERATING PRESSURE:

Liquids
Aluminum and brass meters: 3500 PSIG (240 Bar)
Stainless steel meters: 6000 PSIG (410 Bar)
Air/Gas
Aluminum and brass meters: 600 PSIG (40 Bar)
Stainless steel meters: 1000 PSIG (69 Bar)

MAXIMUM OPERATING TEMPERATURE:

H-Series: 400°F (204°C)
J-Series: 600°F (315°C)

STANDARD CALIBRATION FLUIDS:

Oil meters: DTE 25® @ 110°F (43°C), 0.873 sg
Water meters: water @ 70°F (21°C), 1.0 sg
Air meters: air @ 70°F (21°C), 1.0 sg & 100 PSIG (6.8 bar)

FILTRATION REQUIREMENTS:

74 micron filter or 200 mesh screen minimum

MATERIALS OF CONSTRUCTION:

Window Tube: Pyrex®

Window Seals: PTFE

Casing & End Ports: Anodized Aluminum, Brass, or Stainless Steel

Seals:
H-Series (400°F) : FKM w/ PTFE backup
J-Series (600°F): FFKM w/ PTFE backup

Transfer Magnet: PTFE coated Alnico

All other internal parts: Stainless steel

The post HIGH TEMPERATURE FLOW METER appeared first on Amet Co.,Ltd.

PNEUMATIC VARIABLE AREA FLOW METER

Alex — Fri, 10 Mar 2023 10:01:57 +0000

Pneumatic Flow Meters are ideal for monitoring air compressor outputs, pneumatic tool air consumption, and industrial gas flows. The rugged and reliable design includes all metal pressure vessels, allowing safe installation in industrial systems and industries. Enjoy the unrestricted mounting capabilities and easy installation with multiple ports available.

MEASURING ACCURACY:

±2.5% of full scale in the center third of the measuring range; ±4% in upper and lower thirds

REPEATABILITY:

±1% of full scale

FLOW MEASURING RANGE:

2-1300 SCFM @ 100 PSIG (1-600 LPS)

MAXIMUM OPERATING PRESSURE:

Aluminum & Brass: 600 PSIG (40 Bar)
Stainless Steel: 1000 PSIG (69 Bar)

MAXIMUM OPERATING TEMPERATURE:

240°F (116°C) Note: For operation to 600°F (316°C), see our High Temp datasheet.

STANDARD CALIBRATION FLUIDS:

Air @ 70°F (21°C), 1.0 sg and 100 PSIG (6.8 Bar)

FILTRATION REQUIREMENTS:

74 micron filter or 200 mesh screen minimum

MATERIALS OF CONSTRUCTION (NON-WETTED COMPONENTS):

Window Tube: Polycarbonate
Window Seals: Buna-N®

MATERIALS OF CONSTRUCTION (WETTED COMPONENTS):

Casing & End Ports: Anodized Aluminum, Brass, or Stainless Steel
Seals:

Aluminum: Buna-N® (STD),EPR, FKM, or FFKM
Brass: Buna-N® (STD),EPR, FKM, or FFKM
Stainless Steel: FKM with PTFE backup (STD), Buna-N®, EPR or FFKM

Transfer Magnet: PTFE coated Alnico
All other internal parts: Stainless steel

The post PNEUMATIC VARIABLE AREA FLOW METER appeared first on Amet Co.,Ltd.

CLEARVIEW VALUE FLOW METER

Alex — Fri, 10 Mar 2023 09:04:19 +0000

The ClearView Value Flow Meter is used for water and hydraulic oil flow measurement. This flow meter is an economical way to monitor municipal pressure water flows, observe case drain flows, and verify pump outputs. The transparent body on this variable area flow meter allows for visual inspection of fluid conditions to diagnose any problems at a glance.

MEASURING ACCURACY:

±2.0% of full scale

REPEATABILITY:

±1% of full scale

FLOW MEASURING RANGE:

1-30 GPM (5-110 LPM)

MAXIMUM OPERATING PRESSURE:

325 PSIG (22.4 Bar)

MAXIMUM OPERATING TEMPERATURE:

ClearView H2O: 200°F (93°C) (for water)

ClearView+: 250°F (121°C)

STANDARD CALIBRATION FLUIDS:

Oil meters: DTE 25® @ 110°F (43°C), 0.873 sg

Water meters: tap water @ 70°F (21°C), 1.0 sg

FILTRATION REQUIREMENTS:

74 micron filter or 200 mesh screen minimum

MATERIALS OF CONSTRUCTION:

End Ports: Brass, Ryton®

Seals: Viton

Spring: Stainless Steel

Body: ClearView H2O – Polycarbonate, Clearview+ – Polysulfone

Indicator: Polysulfone

The post CLEARVIEW VALUE FLOW METER appeared first on Amet Co.,Ltd.

HYDRAULIC TEST ANALYZER

Alex — Fri, 10 Mar 2023 08:08:21 +0000

The Hydraulic Test Analyzer is used to diagnose faults in hydraulic circuits, determine horsepower, and test for component wear and cylinder leakage. Available in aluminum or stainless steel, this variable area flow meter offers complete troubleshooting and predictive maintenance so you can plan component repairs and strategized pump, valve, motor, and cylinder rebuilding. The compact and rugged design includes a complete hydraulic system test analyzer small enough to fit in a tool box. No batteries or electrical power are required to power this multi-measurement analyzer for simultaneous measurement of flow, pressure, and temperature.

MEASURING ACCURACY:

Flow: ±2% of full scale
Pressure: ±2.5% of full scale
Temperature: ±2.5% of full scale

REPEATABILITY:

±1% of full scale – all measurements

FLOW MEASURING RANGE:

Flow: 0.1–150 GPM (0.5-550 LPM)
Temperature: 0–250°F (-20–120°C)

MAXIMUM OPERATING PRESSURE:

Aluminum Meters: 3000 PSIG (200 Bar)
Stainless Steel Meters: 5000 PSIG (340 Bar)

MAXIMUM OPERATING TEMPERATURE:

240°F (116°C)

STANDARD CALIBRATION FLUID:

Oil meters: DTE 25® @ 110°F (43°C), 0.873 sg

FILTRATION REQUIREMENTS:

74 micron filter or 200 mesh screen minimum

VISCOSITY

Standard viscosities up to 110 cSt

The post HYDRAULIC TEST ANALYZER appeared first on Amet Co.,Ltd.

CASE DRAIN FLOW METER

Alex — Fri, 10 Mar 2023 07:50:03 +0000

The Case Drain Flow Meter is a Variable Area Flow Meter offering a low cost alternative for monitoring pump performance and identifying required maintenance without interrupting operation. This meter is available for oil or water flow measurement. The superior exterior design of this flow measurement solution is weather-tight for use in outdoor environments and in systems with wash-down requirements.

MEASURING ACCURACY

±5.0% of full scale

REPEATABILITY

±1% of full scale

FLOW MEASURING RANGE

0.1-30 GPM (0.5-115 LPM)

MAXIMUM OPERATING PRESSURE

1000 PSIG (69 Bar)

MAXIMUM OPERATING TEMPERATURE

240°F (116°C)

STANDARD CALIBRATION FLUIDS:

Oil meters: DTE 25® @ 110°F (43°C), 0.873 sg

Water meters: tap water @ 70°F (21°C), 1.0 sg

FILTRATION REQUIREMENTS

74 micron filter or 200 mesh screen minimum

MATERIALS OF CONSTRUCTION (NON-WETTED COMPONENTS):

Window Tube: Polycarbonate

Window Seals: Buna-N

MATERIALS OF CONSTRUCTION (NON-WETTED COMPONENTS):

Casing: Anodized Aluminum

End Ports: Non-Anodized Aluminum

Seals: Buna-N

Transfer Magnet: PTFE coated Alnico

All other internal parts: Stainless steel

The post CASE DRAIN FLOW METER appeared first on Amet Co.,Ltd.

BI-DIRECTIONAL VARIABLE AREA FLOW METER

Alex — Fri, 10 Mar 2023 04:46:55 +0000

The Bi-Directional Variable Area Flow Meter is a high performing oil and water meter available in aluminum, brass, or stainless steel to meet system requirements. It measures bi-directional flow of oils and water, such as in test kits and mobile hydraulic systems. The high pressure operation, multiple ports available, and unrestricted mounting make this flow meter versatile, customizable, and easy to install. The all metal pressure vessels provide a safe and reliable, performance.

MEASURING ACCURACY:

±2.0% of full scale

REPEATABILITY:

±1% of full scale

FLOW MEASURING RANGE:

0.5-100 GPM (2-375 LPM)

MAXIMUM OPERATING PRESSURE:

Aluminum and brass meters: 3500 PSIG (240 Bar), Stainless steel meters: 6000 PSIG (410 Bar)

MAXIMUM OPERATING TEMPERATURE:

240°F (116°C) Note: for operation to 600°F (316°C), see our High Temperature Data sheet.

STANDARD CALIBRATION FLUIDS:

Oil meters: DTE 25® @ 110°F (43°C), 0.873 sg
Water meters: tap water @ 70°F (21°C), 1.0 sg

FILTRATION REQUIREMENTS:

74 micron filter or 200 mesh screen minimum

MATERIALS OF CONSTRUCTION:

Window Tube: Polycarbonate

Window Seals: Buna-N, PTFE option

Casing & End Ports: Anodized Aluminum, Brass, or Stainless Steel

Seals: Buna-N, optional EPR, FKM, or FFKM

Transfer Magnet: PTFE coated Alnico

All other internal parts: Stainless steel

The post BI-DIRECTIONAL VARIABLE AREA FLOW METER appeared first on Amet Co.,Ltd.

Lake Monitors Variable Area Flow Monitors

Alex — Fri, 10 Mar 2023 02:45:56 +0000

The LAKE Basic Inline Variable Area flow meter is ideal for monitoring pump performance and oil or water flows through hydraulic circuits and cooling systems. Often referred to as “rotameters,” Lake’s Basic meters are a low cost alternative to other flow meter types and are available in numerous materials of construction, including aluminum, brass and stainless steel to meet system and media requirements. The superior design not only makes this flow meter weather-proof for outdoor environments and wash-downs, but also reliable offering maintenance-free performance.

Specification

MEASURING ACCURACY: ±2.0% of full scale

REPEATABILITY: ±1% of full scale

FLOW MEASURING RANGE: 0.1-150 GPM (0.5-550 LPM)

MAXIMUM OPERATING PRESSURE: Aluminum and brass meters: 3500 PSIG (240 Bar), Stainless steel meters: 6000 PSIG (410 Bar)

MAXIMUM OPERATING TEMPERATURE: 240°F (116°C) Note: for operation to 600°F (316°C), see our High Temperature Data sheet.

STANDARD CALIBRATION FLUIDS:
Oil meters: DTE 25® @ 110°F (43°C), 0.873 sg
Water meters: tap water @ 70°F (21°C), 1.0 sg

FILTRATION REQUIREMENTS: 74 micron filter or 200 mesh screen minimum

MATERIALS OF CONSTRUCTION:
Window Tube: Polycarbonate
Window Seals: Buna-N, PTFE option
Casing & End Ports: Anodized Aluminum, Brass, or Stainless Steel
Seals: Buna-N, optional EPR, FKM, or FFKM
Transfer Magnet: PTFE coated Alnico
All other internal parts: Stainless steel

The post Lake Monitors Variable Area Flow Monitors appeared first on Amet Co.,Ltd.