Particle Counter - Amet Co.,Ltd

Extech VPC260 : 6-Channel Particle Counter

Alex — Tue, 11 Aug 2026 09:56:35 +0000

The VPC260 is a 6-channel particle counter for monitoring workplace environmental health and quality. Measure up to 6 channels of particle sizes plus air temperature, relative humidity, dew point, and wet bulb. Check indoor air quality for exhaust, smoke, respirable crystalline silica dust (RCS), airborne combustible dust, and other harmful air pollutants.

General
Air Temperature	0°C to 50°C (32°F to 122°F); Accuracy: ±1.8°F (±1.0°C)
Coincidence Loss	10% @ 2,000,000 counts per ft³
Counting Efficiency	50% @ 0.3 µm (100% for particles >0.5 µm)
Dew Point	0°C to 50°C (32°F to 122°F)
Max Flow Rate	0.035 ft³/min (1.0 L/min) controlled by internal pump
Particle Size	0.3 µm, 0.5 µm, 1.0 µm, 2.5 µm, 5.0 µm, 10 µm
Readout Modes	Cumulative, Differential, Concentration
Relative Humidity	0 to 100% RH; Accuracy: ±3.5% RH (20% to 80% RH)
Size [L × W × H]	238 mm × 73 mm × 50 mm (9.3 in × 2.8 in × 2.0 in)
Storage Capacity	1000 data sets
Wet Bulb	0°C to 50°C (33°F to 122°F)

The post Extech VPC260 : 6-Channel Particle Counter appeared first on Amet Co.,Ltd.

Particle Counter Device PCE-MPC 30

Admin Amet — Thu, 18 Mar 2021 03:36:28 +0000

Particle Counter Device with data logger / HCHO measurement / battery for mobile use / 2.8 “TFT display / measurement of mass concentration / data storage on SD card

This Particle Counter Device has many functions. With the Particle Counter Device it is possible to determine the number of particles in the size of 0.3, 2.5 and 10 µm. In addition to measuring the particles, the Particle Counter Device can also measure the PM 2.5 and PM 10 mass concentration. The mass concentration of the Particle Counter Device determines the weight of the particles on one cubic meter.

In addition to particle measurement, the Particle Counter Device can also determine the formaldehyde content in ppm. During this HCHO measurement, the temperature, the ambient humidity and the dew point are determined and displayed by the Particle Counter Device. As a further important property, the Particle Counter Device can also store data. It is therefore possible with the Particle Counter Device to evaluate all measured values after a measurement.

– Particle counter, HCHO, temperature measurement

– Measured value recording for later analyzes

– Large 2.8 “LC display, 320 x 240 pixels

– Mass concentration PM 2.5 and PM 10

– Battery for mobile use

– Dew point and wet bulb temperature

Measurable particle sizes	PM 2.5 and PM 10
Measuring range	0 … 2000 µg / m³
Resolution	1 µg / m³

Particle counter
Measurable particle sizes	0.3, 2.5, 10 µm
Flow rate	2.83L / min (0.1 ft³)
Counting efficiency	50% at 0.3 µm;
	100% with particle size> 0.45 µm
Coincidence error	<5% at 2,000,000 particles per ft³
Data storage	5000 data records (micro SD card)
Counting modes	cumulative, differential, concentration

HCHO
Measuring range	0.01 … 5.00 ppm
Accuracy	± 5%
Resolution	0.01 ppm

Air temperature and relative humidity
Measuring range air temperature	0 … 50 ° C, 32 … 122 ° F
Measuring range dew point	0 … 50 ° C, 32 … 122 ° F
Relative humidity measuring range	0 … 100% RH
Air temperature measurement accuracy	10 … 40 ° C: ± 1 ° C, ± 1.8 ° F
	Others: ± 2 ° C, ± 3.6 ° F
Measuring accuracy dew point temperature	10 … 40 ° C: ± 1 ° C, ± 1.8 ° F
	Others: ± 2 ° C, ± 3.6 ° F
Relative humidity accuracy	0 … 20% rel. Humidity: ± 5%
	20 … 80% rel. Humidity: ± 3.5%
	80 … 100% rel. Fencing: ± 5%

More specifications
Operating conditions	0 … +50 ° C, 10 … 90% rel. humidity,
	not condensing
Storage conditions	-10 … +60 ° C, 10 … 90% rel. humidity,
	not condensing
Display	2.8 “, 320 x 240 pixels, backlit color LCD
Power supply mains adapter	Primary: 100 … 240 V AC, 50/60 Hz, 0.6 A.
	Secondary: 9 V DC, 1500 mA
Power supply battery	7.4 V, 1200 mAh, 8.88 Wh
Battery Life	approx. 4 hours in continuous operation
Battery recharge time	approx. 2 hours with AC adapter
Dimensions	240 x 75 x 57 mm
Weight	570 g

The post Particle Counter Device PCE-MPC 30 appeared first on Amet Co.,Ltd.

Particle Counter PCE-AQD 20-ICA Incl. ISO Calibration Certificate

Admin Amet — Thu, 18 Mar 2021 03:28:35 +0000

Particle Counter PCE-AQD 20-ICA incl. ISO calibration certificate

Air quality data logger for 5 parameters / Measures temperature, humidity, CO2, PM2.5 and air pressure / SD storage / XLS format / Large LCD / Power adapter and battery operation

The air quality data logger PCE-AQD 20 is an ideal measuring device for monitoring the air quality at workplaces. The air quality data logger is ideal for continuous logging of air temperature, humidity, CO2, PM2.5 and air pressure. All these parameters give the occupational safety expert information about the air quality. The measured values are stored by the CO2 air quality data logger on an SD memory card.

The format is XLS, so the measured values can be read directly into Excel, without having to be incorporated into a new software. The measured values are displayed on the large, illuminated display. The air quality data logger is operated by batteries or 9 V power supply unit. As a special feature, this air quality data logger is equipped with an alarm function. This offers the possibility to inform the user about an exceeding of temperature, air humidity or dust load. In addition to the measured values, the air quality data logger also informs about the current time.

– 5 measuring functions
– Excel data logger on SD card
– Large display
– Battery and power adapter operation
– Ideal for workplace monitoring
– Alarm function
– Incl. ISO calibration certificate

Measurement function PM2.5
Measuring range	0 … 250 μm / m³
Resolution	1 μm / m³
Accuracy	± (10% of rdg. + 15 μm)

Measuring function humidity
Measuring range	5 … 95% rh
Resolution	0.1% RH
Accuracy	> 70% RH: ± (3% of the prev
	+ 1% RH)
	<70% RH: ± 3% RH

Measuring function temperature
Measuring range	0 … 50°C / 32 … 122°F
Resolution	0.1°C / 0.18°F
Accuracy	± 0.8°C / 1.44°F

Measurement function CO2
Measuring range	0 … 10,000 ppm
Resolution	1 ppm
Accuracy	< 1000 ppm: ± 40 ppm
	< 3000 ppm: ± (50 ppm + 3% of rdg.)
	> 3000 ppm: ± (50 ppm + 5% of rdg.)

Measuring function air pressure
Measuring range	10 … 1100 hPa
Resolution	0.1 hPa
Accuracy	± 1.5 hPa

Display	LCD display with backlight
Storage	SD card max. 32 GB
Storage rate	2 … 3,600 s
Memory error	< 0.1% of the completely stored data
Display	Hold, Max, Min
Measuring rate	About 1 s
Interface	Serial for live visualization on computers
	(Data cable SOFT-LUT-USB sold separately)
Alarm output	OC output 24V / 70-mA DC
Power supply	6 x 1.5V AA battery
	9V / 1 A power adapter
Current consumption	230-mA without lighting
	approx. 250-mA with lighting
Operating conditions	0 … 50°C / 32 … 122°F, max. 80% rh
Weight	About 387 g / < 1 lb
Dimensions	164 x 93 x 72 mm / 6.5 x 3.7 x 2.8 in

The post Particle Counter PCE-AQD 20-ICA Incl. ISO Calibration Certificate appeared first on Amet Co.,Ltd.

Air Quality Monitoring Particle Counter PCE-MPC 20

Admin Amet — Thu, 18 Mar 2021 03:22:54 +0000

Particle collector PCE-MPC 20

Dust measuring device for the measurement of pollutant content of the atmosphere / With data memory / USB interface / Mass concentration / Particle counter

The dust measuring device PCE-MPC 20 is a particle counter that measures the particles in the atmosphere. The measurable particle sizes of the dust measuring device are 0.3, 2.5 and 10 μm. In addition to the particle counter function, the dust meter also measures the mass concentrations PM2.5 and PM10. The built-in high-performance pump ensures a sufficient flow rate at the dust measuring device. In addition, the dust meter can also measure the temperature, humidity and dew point.

The measured values can be read directly on the display of the dust measuring device. Data storage is also possible with the dust measuring device in order to analyze the measured values after a measuring process. The battery used ensures a mobile application. This allows a mobile continuous operation of about 4 hours. A dust measuring device is used wherever a possible health hazard due to fine dust could occur. These include pollution from incineration, manufacturing, energy production, vehicle engine emissions, and the pollution that the construction industry generates.

– Mass concentration PM2.5 / PM10
– Data memory up to 5,000 data sets
– Flow rate 2.83 l / min
– Display with graphic real-time diagram
– Battery or AC charger operation possible
– Alarm function

Mass concentration
Measurable particle sizes	PM2.5 / PM10
Measuring range mass concentration	0 … 2000 μg / m³
Resolution	1 μg / m³

Particle counter
Measurable particle sizes	0.3, 2.5 and 10 μm
Flow rate	2.83 l / min (0.1 ft³)
Coincidence error	< 5% at 2,000,000 particles per ft³
Counting efficiency	50% at 0.3 μm;
	100% with particle size > 0.45 μm
Counting modes	Cumulative, differential, concentration

Measurement of air temperature and relative humidity
Measuring range air temperature	0 … 50°C / 32 … 122°F
Measuring range dew point temperature	0 … 50°C / 32 … 122°F
Measuring range relative humidity	0 … 100%
Measuring accuracy air temperature	10 … 40°C / 50 … 104°F: ± 1.0°C / 1.8°F
	Others: ± 2.0°C / 3.6°F
Measuring accuracy dew point temperature	10 … 40°C / 50 … 104°F: ± 1.0°C / 1.8°F
	Others: ± 2.0°C / 3.6°F
Measuring accuracy relative humidity	0 … 20% rel. Humidity: ± 5%
	20 … 80% rel. Humidity: ± 3.5%
	80 … 100% rel. Humidity: ± 5%
Operating conditions	0 … 50°C / 32 … 122°F, 10 … 90% rel. humidity,
	Not condensing
Storage conditions	-10 … 60°C / 14 … 140°F, 10 … 90% rel. humidity,
	Not condensing
Data storage	5,000 data sets (Micro SD card)
Display	2.8″, 320 x 240 pixels
	Backlit color LCD
Power supply Charger	Rechargeable battery 1200-mAh, 7.4V 100 .. 240 VAC, 50 or 60 Hz
Battery Life	About 4 hours in continuous operation
Battery recharge time	About 2 hours with AC adapter
Dimensions	240 x 75 x 57 mm / 9.4 x 3 x 2.2 in
Weight	570 g / 1.3 lbs

The post Air Quality Monitoring Particle Counter PCE-MPC 20 appeared first on Amet Co.,Ltd.

Particle Counter PCE-AQD 20

Admin Amet — Thu, 18 Mar 2021 02:39:37 +0000

Particle Counter PCE-AQD 20

Air quality data logger for 5 parameters / Measures temperature, humidity, CO2, PM2.5 and air pressure / SD storage / XLS format / Large LCD / Power adapter and battery operation

– 5 measuring functions
– Excel data logger on SD card
– Large display
– Battery and power adapter operation
– Ideal for workplace monitoring
– Alarm function

Measurement function PM2.5
Measuring range	0 … 250 μm / m³
Resolution	1 μm / m³
Accuracy	± (10% of rdg. + 15 μm)

Measuring function humidity
Measuring range	5 … 95% rh
Resolution	0.1% RH
Accuracy	> 70% RH: ± (3% of the prev
	+ 1% RH)
	<70% RH: ± 3% RH

Measuring function temperature
Measuring range	0 … 50°C / 32 … 122°F
Resolution	0.1°C / 0.18°F
Accuracy	± 0.8°C / 1.44°F

Measurement function CO2
Measuring range	0 … 10,000 ppm
Resolution	1 ppm
Accuracy	< 1000 ppm: ± 40 ppm
	< 3000 ppm: ± (50 ppm + 3% of rdg.)
	> 3000 ppm: ± (50 ppm + 5% of rdg.)

Measuring function air pressure
Measuring range	10 … 1100 hPa
Resolution	0.1 hPa
Accuracy	± 1.5 hPa

Display	LCD display with backlight
Storage	SD card max. 32 GB
Storage rate	2 … 3,600 s
Memory error	< 0.1% of the completely stored data
Display	Hold, Max, Min
Measuring rate	About 1 s
Interface	Serial for live visualization on computers
	(Data cable SOFT-LUT-USB sold separately)
Alarm output	OC output 24V / 70-mA DC
Power supply	6 x 1.5V AA battery
	9V / 1 A power adapter
Current consumption	230-mA without lighting
	approx. 250-mA with lighting
Operating conditions	0 … 50°C / 32 … 122°F, max. 80% rh
Weight	About 387 g / < 1 lb
Dimensions	164 x 93 x 72 mm / 6.5 x 3.7 x 2.8 in

The post Particle Counter PCE-AQD 20 appeared first on Amet Co.,Ltd.

Air Quality Monitoring Particle Counter PCE-MPC 10

Admin Amet — Wed, 17 Mar 2021 09:51:52 +0000

PCE-MPC 10 Air Quality Monitoring Particle Counter
Portable handheld device for monitoring particulate matter (PM) concentrations in the air / 2.5 µm and 10 µm particle sizes / Measures air temperature and relative humidity / Internal memory stores up to 5000 date-and-time-stamped data sets / Integrated data logger with adjustable sampling time

PCE-MPC 10 is a portable handheld particle counter used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this particle counter also measures air temperature and relative humidity (RH). The particle counter can be powered either by the rechargeable battery or the USB port. The USB port also is used to charge the battery. The particle counter takes measurements even while the battery is charging, allowing for uninterrupted IAQ monitoring. The integrated data logger has an adjustable sampling time of 30 seconds, 1 minute, 2 minutes or 5 minutes, while the internal memory stores up to 5000 date-and-time-stamped data sets.

The particle counter displays all measurements simultaneously on the device’s 2″ full-color LCD screen. Temperature units can be shown in either degrees Celsius (°C) or Fahrenheit (°F). A scale below the measured values provides a visual warning via a band of colors increasing from green (safe) to violet (extreme danger). This visual color-coding system makes it easy to recognize when PM concentration levels become dangerous, allowing for quick action.

When inhaled, PM 2.5 and PM 10 particles can settle deep into the lungs and result in damaging health effects. Since the PCE-MPC 10 particle counter monitors PM 2.5 and PM 10 particles, the device has many practical health and safety applications. Heating, ventilation and air conditioning (HVAC) technicians use PM 2.5 and PM 10 particle counters for HVAC system performance and filtration audits. In addition, industrial hygienists and workplace safety professionals rely on PM 2.5 and PM 10 particle counters when evaluating occupational health and safety risks related to hazardous and combustible dust.

– Particulate matter (PM) channels: PM 2.5, PM 10
– Particle sizes (in micrometers): 2.5 µm, 10 µm
– Temperature measuring range: 0 … +50 °C / +32 … +122 °F
– Humidity measuring range: 0 … 100 % RH
– 2″ full-color LCD with user-friendly graphics
– 220 x 176 pixel display resolution
– Displays temperature in degrees Celsius (°C) or Fahrenheit (°F)
– Powered by rechargeable battery or AC power (via USB port)
– Portable handheld design for indoor air quality (IAQ) monitoring in the field and on the go
– Includes a stand for attaching to the thread on the back of the device
– Features an internal memory for storing up to 5000 data sets
– Saved data is stamped with the time and date
– Takes measurements even while the battery is charging
– Integrated data logger with adjustable sampling time: 30 seconds, 1 minute, 2 minutes or 5 minutes
– Programmable alarm and automatic power-off battery-saving functionality
– Backed by a 2-year warranty against manufacturer defects

General device specifications
Display	2″ full-color LCD
Display resolution	220 x 176 pixels
Power supply	Rechargeable battery or USB port
Charging	Takes measurements even while the battery is charging
Sampling time	Adjustable interval: 30 seconds, 1 minute, 2 minutes or 5 minutes
Memory	Internal, stores up to 5000 date-and-time-stamped data sets
Data interface	USB port

Particle specifications
Particulate matter channels	PM 2.5 / PM 10
Particle sizes (in micrometers)	2.5 µm, 10 µm
Particle concentrations	0 … 2000 μg / m³
Resolution	1 μg / m³

Temperature specifications
Temp. measuring range	0 … +50 °C / +32 … +122 °F
Accuracy	± 1 °
Resolution	0.1 °
Units	Degrees Celsius (°C) or Fahrenheit (°F)

Relative humidity (RH) specifications
Humidity measuring range	0 … 100 % RH
Accuracy	± 3.5 % RH (20 … 80 % RH) ± 5 % RH (0 … 20 % RH / 80 … 100 % RH)
Resolution	0.1 % RH

The post Air Quality Monitoring Particle Counter PCE-MPC 10 appeared first on Amet Co.,Ltd.

Particle Counter PCE-RCM 12

Admin Amet — Wed, 17 Mar 2021 07:53:16 +0000

Particle Counter PCE-RCM 12
Air quality monitor for indicative measurement of environmental conditions / Determination of CO2, HCHO, particulate matter (PM2.5 / PM10) / Temperature und relative humidity / 3″ TFT LCD Display

The particle counter PCE-RCM 12 is used for indicative testing of environmental parameters. The particle counter PCE-RCM 12 enables the measurement of CO2, fine dust, temperature and relative humidity. The bright display of the particle counter provides information about these parameters. Environmental monitoring can be done continuously with the particle counter for up to five hours without the device being connected to a power source.

For permanent measurement, the particle counter can be connected to AC power via a USB interface. The rechargeable battery will be recharged within two hours if the air quality monitor is turned off. When measuring carbon dioxide, the meter has a wide measuring range from 0 to 9,999 ppm. The display of the concentrations is further facilitated by the use of a color rating scale, as this provides direct information about the air quality to the user.

In addition to the indicative measurement of formaldehyde, which can be harmful to health, an indicative measurement of particulate matter pollution can also be carried out. A distinction is made between particles with a maximum diameter of up to 10 μm (PM10) and particles up to a diameter of 2.5 μm (PM2.5).

– Measurement of CO2 and formaldehyde
– Indication of room temperature and humidity
– Particulate matter measurement (PM2.5 / PM10)
– Large CO2 measurement range up to 9999 ppm
– Changing display of the measured values
– Memory for up to 5000 measuring groups
– Date and time display
– 3″ large TFT-LCD display
– Safe and easy handling

Measuring range fine dust	PM2.5 / PM10
Measuring range particle measurement	0 … 2000 µg/m³
Resolution particle measurement	1 µg/m³

Measuring range CO2	0 … 9999 ppm
Accuracy CO2	±5% of measured value or ±75 ppm
Resolution CO2	1 ppm

Measuring range formaldehyde	0.00 … 5.00 mg/m³
Accuracy formaldehyde	±5% of measured value
Resolution formaldehyde	0.01 mg/m³

Measuring range humidity	0 … 100% r.H.
Accuracy humidity	±3.5% r.H. (at 20 … 80% r.H.) ± 5% r.H. (at 0 … 20% r.H. / 80 … 100% r.H)
Resolution humidity	0.1% r.H.%

Measuring range temperature	-20 … 70°C / -4 … 158°F
Accuracy temperature	±2°C / 3.6°F
Resolution temperature	0.1°C / 0.18°F

Sound sensor	Wake up function to APO
Power supply	2400-mAh, rechargeable battery
Battery life	Continuous measurement for up to 5 hours
Charging	Via USB 5V / 1 A
Charging time	2 hours (when switched off)
Automatic sleep mode	Adjustable if necessary
Display	3″ TFT LCD Display, 240 x 400 pixel
Data storage	5000 measurement groups
Operating temperature	0 … 50°C / 32 … 122°F
Storage temperature	-10 … 60°C / 14 … 140°F
Dimensions	85 x 75 x 155 mm / 3.3 x 2.9 x 6.1 in
Weight	360 g / < 1 lb

The post Particle Counter PCE-RCM 12 appeared first on Amet Co.,Ltd.

Air Quality Meter / Particle Counter PCE-RCM 11

Admin Amet — Wed, 17 Mar 2021 07:12:02 +0000

Air Quality Meter / Particle Counter

Particle counter for orienting measurement of the environmental conditions / Determination of HCHO, fine dust (PM2.5 / PM10) / Temperature and relative humidity / 3 “TFT LCD display

The air quality monitor PCE-RCM 11 serves the indicative examination of environmental parameters. The air quality monitor enables the measurement of fine dust, temperature and relative humidity. The bright display of the air quality monitor provides information about the already mentioned parameters. Environmental monitoring can be done continuously with the Air Quality Monitor for up to five hours without the device being connected to a power source.

For permanent measurement, the air quality monitor can be connected to the mains via a USB interface. The rechargeable battery will be recharged within two hours if the air quality monitor is turned off. The display of the concentrations is further simplified by the use of a color rating scale, as this directly provides information about the air quality to the user.

In addition to the indicative measurement of formaldehyde, which can be harmful to health, there is also an orienting measurement of particulate matter pollution to be carried out. A distinction is made between particles with a maximum diameter of up to 10 μm (PM10) and particles up to a diameter of 2.5 μm (PM2.5).

Health problems with paints, furniture and adhesives

Eye irritation, headache or concentration problems: paints, furniture and adhesives can outgas the pollutants that affect the health. Therefore, the quality of the room air should be continuously monitored. Simply and precisely, this is done with a measuring device for testing the living-room air. Designed specifically for this purpose, the PCE Instruments meter is a real all-rounder when it goes about carrying out a living-room air test. During the room air test, the meter quickly and precisely determines several environmental parameters that are important for health and well-being. The living-room air test enables the effective and uncomplicated measurement of the volatile organic compounds (TVOC), particulate matter, temperature, formaldehyde and relative humidity. The display also informs about date and time.

Due to the living-room air test, one may keep the air quality under control, and the colour evaluation scale of the measuring device makes it particularly convenient. The scale of the measuring instrument serves as an indicator and facilitates the orientation for the user: as soon as a limit is exceeded, this is shown immediately in colour on the display. If desired, the device also makes an audible signal sound during the living-room air test, in case of a potential danger. This function is useful, for example, when measuring pollutants in the indoor air. The living-room air test with the particle counter allows, for example, the effective determination of the particulate matter pollution. Here, a distinction is made between the particles with a maximum diameter of up to 10 μm (PM10) and the particles with a diameter of up to 2.5 μm (PM2.5). In addition, the living-room air test gives precise information about the formaldehyde concentration in the room air. During the measurement of the volatile organic compounds (TVOD), the testing is possible within a measuring range from 0 to 9.99 mg / m³. For carrying out the living-room air test, the manufacturer has also equipped the particle counter with a large memory for 5000 measuring groups so that the determined values could also be retrieved later. In addition, during the living-room air test, the measuring device provides a reliable information about the temperature (-20 degrees Celsius to +70 degrees Celsius) and the humidity (0 to 100 percent RH). The measured values are updated every second.

More information about the usage of the particle counter

During the living-room air test, the easy-to-read screen of the measuring instrument alternately displays the determined values. The user also has the opportunity to use the device completely independently for a while, without connection to a power source. Only after five hours of continuous operation the particle counter needs new energy. Within two hours, the battery of the meter can then be fully charged again to perform a new living-room air test. In order to enable a permanent measurement of the environmental conditions, the manufacturer has equipped the measuring device for the living-room air test with a USB interface. In this way, the user can connect the meter to a power source during a living-room air test. If necessary, the particle counter can also be set into an automatic sleep mode. Due to a built-in noise sensor, the meter automatically switches on as soon as it detects the noise and starts the living-room air test. If desired, this sensor can also be deactivated by the user.

Application areas

The particle counter for the living-room air test is compact and flexible in use, it is therefore ideal for monitoring the air quality in different indoor areas in the professional and private sector. Its multiple functions and the ability to capture multiple environmental parameters make it the ideal instrument for factories, workplaces, schools and kindergarten day-care centres. Also, in the private sector, the preference during the living-room air quality test is given to this device due to the ease of use and the modern design.

– measurement of formaldehyde

– indication of the room temperature and humidity

– particulate matter measurement (PM2,5 / PM10)

– changing display of the measured values

– memory for up to 5000 measuring groups

– date and time display

– USB interface

– 3 “large TFT-LCD display

– safe and easy handling

Measuring range fine dust	PM2.5 / PM10
Measuring range particle measurement	0 … 2000 μg / m³
Resolution particle measurement	1 μg / m³

Measuring range TVOC (Volatile Organic Substances)	0.00 … 9.99 mg / m³
Accuracy TVCO	± 5% of the measuring range
Resolution TVCO	0.01 mg / m³


Measuring range formaldehyde	0.00 … 5.00 mg / m³
Accuracy formaldehyde	± 5% of the measuring range
Dissolution formaldehyde	0.01 mg / m³

Measuring range humidity	0 … 100% rh
Accuracy of humidity	± 3.5% RH (at 20 … 80% RH) ± 5% RH (at 0 … 20% RH / 80 … 100% RH)
Resolution Humidity	0.1% RH

Measuring range temperature	-20 … 70°C / -4 … 158°F
Accuracy temperature	± 2°C / 3.6°F
Resolution temperature	0.1°C / 0.18°F

Sound sensor	Wake up to APO
Power supply	2400-mAh, rechargeable battery
Battery life	Continuous measurement for up to 5 hours
Charging	Via USB 5V / 1 A
Charging time	2 hours (when switched off)
Automatic sleep mode	Adjustable if necessary
Display	3″ TFT LCD display, 240 x 400 pixels
Data storage	5000 measuring groups
Operating temperature	0 … 50°C / 32 … 122°F
Storage temperature	-10 … 60°C / 14 … 140°F
Dimensions	85 x 75 x 155 mm / 3.3 x 3 x 6.1 in
Weight	360 g / < 1 lb

The post Air Quality Meter / Particle Counter PCE-RCM 11 appeared first on Amet Co.,Ltd.

Particle Counter PCE-RCM 15

Admin Amet — Wed, 17 Mar 2021 07:06:34 +0000

PCE-RCM 15 Particle counter
Monitoring device for indoor air quality measurement / Measures 7 air quality parameters simultaneously / Built-in alarm function

The air quality measuring device is specially designed for monitoring the ventilation quality of interiors. Among other things, the PCE-RCM 15 air quality meter measures the parameters for PM1, PM2.5, PM10, TVOC, formaldehyde, air humidity and temperature. All measured values are displayed on the large display.

Thus, the air quality meter is particularly suitable for applications in offices, schools and other educational institutions but also in living spaces. On the display can be switched by switching between the individual measuring functions. The measured values are processed and visualized both graphically and numerically on the air quality measuring device. In addition to measuring the air quality, the air quality meter has an alarm function.

– Large color display
– 7 in 1 air quality meter
– TVOC, HCHO, Temp., Airf., PM1, PM2.5, PM10 (Only displays in °C)
– Battery and mains operation, A/C power adapter
– 3 different display modes
– Alarm function

Measured quantity of formaldehyde
Measuring range	0 … 1.999 mg / m³
Resolution	0.001 mg / m³
Accuracy	± 5%

Measured TVOC
Measuring range	0 … 9.999 mg / m³
Resolution	0.001 mg / m³
Accuracy	± 10%

Measured variable PM1, PM2.5, PM10
Measuring range	0 … 999 μg / m³
Resolution	1 μg / m³
Accuracy	± 15%

Measured variable temperature
Measuring range	-10 … 45°C / 14 … 113°F (Only displays in °C)
Resolution	0.1°C / 0.18°F (Only displays in °C)
Accuracy	± 1°C / 1.8°F (Only displays in °C)

Measured variable air humidity
Measuring range	20 … 99% rh
Resolution	1% rh
Accuracy	± 5 rf

Display	LC display
Power supply	Li-ion battery 3.7V / 5000-mAh
	Power supply 5V / 2000-mA
Charging socket	Micro USB
Operating conditions	-10 … 50°C / 14 … 122°F, max. 90% rh
Storage conditions	-20 … 50°C / -4 … 122°F, max. 90% rh
Dimensions	24.5 x 11 x 12.5 cm / 9.6 x 4.3 x 4.9 in
Weight	About 515 g / 1.1 lbs

The post Particle Counter PCE-RCM 15 appeared first on Amet Co.,Ltd.

Particle Counter PCE-RCM 16

Admin Amet — Wed, 17 Mar 2021 07:00:24 +0000

Particle counter PCE-RCM 16

Air quality meter for measuring the air quality / 4.3 inch TFT display / Metal housing / Alarm function / TVOC, CO2, PM1, PM 2.5, PM10, temperature, humidity measurement / Rechargeable battery / For enclosed spaces / Limit alarm

The air quality meter PCE-RCM 16 is ideal for monitoring the air quality in homes, businesses or public buildings where people are staying. The 4.3-inch TFT display on the air quality meter is dimensioned so that all measured values can be read directly. Supported measurements on the air quality meter are CO2, TVOC, PM1, PM2.5, PM10, temperature and ambient humidity. On the display of the air quality meter, the measured values are updated every second. As soon as a measured value exceeds the fixed limit, this is visually indicated to the user.

To power the air quality meter can be operated directly via the micro USB port on the back. The built-in battery with the air quality meter is charged via this interface. Thus, the air quality meter is versatile. It should be noted that the measured values settle within 24 hours after switching on the air quality meter.

N.B. the meter is designed to be operated by mains power, and will run only a few hours by the battery.

– 4.3-inch TFT screen
– Many different measuring functions
– Robust metal housing
– Calculation of the air quality index (AQI)
– Rechargeable battery via micro USB
– Adjustable alarm clock
– Different display modes
– Fixed limit function

Measurement function TVOC
Measuring range	0.000 … 9.999 mg / m³
Resolution	0.001 mg / m³
Accuracy	± 10% of the measured value

Measurement function PM1, PM 2.5, PM10
Measuring range	0 … 999 μg / m³
Resolution	1 μg / m³
Accuracy	± 10% of the measured value

Measuring function temperature
Measuring range	0 … 50°C / 32 … 122°F
Resolution	1°C / 1.8°F
Accuracy	± 1°C / 1.8°F

Moisture measurement function
Measuring range	20 … 90% rh
Resolution	1%
Accuracy	± 4%

Measurement function CO2
Measuring range	0 … 5000 ppm
Resolution	1 ppm
Accuracy	± 10% of the measured value

Settling	About 24 hours
Display	TFT display, 4.3 inches
Environmental conditions	0 … 50°C / 32 … 122°F, max. 90% rh
Connection	Micro USB for charging the battery
Power supply	5V / 2A
Battery pack	3000-mAh
Casing	Metal
Dimension	191 x 78 x 67.5 mm / 7.5 x 3 x 2.7 in
Weight	336 g / < 1 lb

The post Particle Counter PCE-RCM 16 appeared first on Amet Co.,Ltd.