Thickness Gauge - Amet Co.,Ltd

Thickness Gauge PCE-USC 30

Admin Amet — Thu, 29 Apr 2021 04:29:39 +0000

Portable thickness gauge for NDT / NDT testing of surfaces / Coating thickness measurement using eddy current / Conductivity measurement of metals according to IACS / Material sorting

The thickness gauge is used in non-destructive material testing. With the eddy current testing device, surface defects and near-surface defects can be made visible. Eddy current testing is an electrical method for testing electrically conductive materials. In the eddy current test, a probe charged with alternating voltage is placed on an electrically conductive test piece. The magnetic field lines generated perpendicular to the workpiece surface induce circular eddy currents close to the surface, creating secondary magnetic fields in the test piece. The secondary fields counteract the primary fields and measurably change them in terms of amplitude and phase. Inhomogeneities and workpiece defects change the eddy current curves and the permeability of the material and thus also the secondary fields. In this way, defects close to the surface can be located and classified.

The thickness gauge is designed for corresponding NDT material tests and can also be used for conductivity measurement and layer thickness determination.

The ergonomic design of the thickness gauge, a weight of less than 1 kg, a battery life of approx. 8 hours, a large selection of probes to cover a wide frequency range up to 3.5 MHz, as well as software for generating reports are good prerequisites for effective and pleasant work.

The thickness gauge is therefore ideally suited for non-destructive material testing in the aerospace sector for component testing of e.g. turbine blades or bores, for welding seam testing and crack testing, for pipeline and container testing in the chemical, oil and gas industry or in the field of mechanical engineering for quality control of semi-finished products, sheet, strip products or individual components. The testing of material properties is also possible via a microstructure comparison, so that checks for mix-ups can also be carried out.

– Large frequency range
– 4.3″ large colour display (TFT)
– NDT testing of surfaces
– Sorting of material
– Frequency range up to 3.5 MHz
– Battery life approx. 8 hours

Frequency range	0.01 … 16000 kHz
Probe voltage supply	0, 5, 1, 2, 4, 6 V
Signal phase shift	0 … 360°
Sampling frequency	0 … 10 kHz
Duration of signal fade-in	0 / 0.5 / 1 / 2 / 3 / 4 seconds
Alarm	circular horizontal line circle sector cut-off
Display	full-colour display (TFT)
Display size	4.3″ (diagonal)
Display resolution	800 x 480 pixels
Amplification adjustment	0 … 100 dB
Filter	low pass filter (1 … 4000 Hz) high pass filter (1 … 4000 Hz) band filter differential filter average value filter
Average interval between measurement errors	4000 hours
Power supply	12 V battery
Battery capacity	4500 mAh
Continuous runtime per battery charge	>8 hours
Operating temperature	-20 … +45 °C
Weight	<0.9 kg
Dimensions	230 x 135 x 98 mm

The post Thickness Gauge PCE-USC 30 appeared first on Amet Co.,Ltd.

Paint Thickness Tester PCE-USC 30

Admin Amet — Thu, 29 Apr 2021 04:27:28 +0000

PCE-USC 30 is a coating thickness gauge designed for the non-destructive testing (NDT) and non-destructive evaluation (NDE) of electrically conductive materials. This portable, handheld thickness meter detects surface defects and measures layer thicknesses using an eddy current. The PCE-USC 30 material tester also measures metal conductivity in accordance with the International Annealed Copper Standard (IACS).

The PCE-USC 30 thickness gauge has myriad applications including weld seam testing, crack detection, metallurgical and material sorting tests, quality assurance and control, aviation component testing of turbine blades, and pipeline and container testing in the chemical, oil and gas industries.
– Frequency range: 0.01 … 16000 kHz
– Visually depicts surface defects on screen
– 4.3″ full-color display (TFT)
– Ergonomic design
– Long battery life

Frequency range: 0.01 … 16000 kHz
Probe voltage supply: 0, 5, 1, 2, 4, 6 V
Signal phase shift: 0 … 360 °
Sampling frequency: 0 … 10 kHz
Duration of signal superimposition: 0 / 0.5 / 1/2/3/4 seconds
Alarm: Circular, horizontal line, circle sector, cut off
Display: Full-color display (TFT)
Display size: 4.3 “(diagonal)
Display resolution: 800 x 480 pixels
Amplification adjustment: 0 … 100 dB
Filters: Low-pass (1 … 4000 Hz), high-pass (1 … 4000 Hz), band, differential, average
Average interval between measurement errors: 4000 hours
Power supply: 12 V battery
Battery capacity: 4500 mAh
Continuous runtime per battery charge: Approx. 8 hours
Operating temperature: -20 … +45 ° C
Weight: Approx. 0.9 kg
Dimensions: 230 x 135 x 98 mm

The post Paint Thickness Tester PCE-USC 30 appeared first on Amet Co.,Ltd.

Coating Thickness Gauge PCE-USC 30

Admin Amet — Thu, 29 Apr 2021 04:23:55 +0000

The post Coating Thickness Gauge PCE-USC 30 appeared first on Amet Co.,Ltd.

Ultrasonic Thickness Gauge PCE-USC 20

Admin Amet — Thu, 29 Apr 2021 04:21:06 +0000

PCE-USC 20 is a portable or benchtop ultrasonic tester or ultrasonic thickness gauge with a 5.7″ TFT color LCD screen. This ultrasound-based thickness meter uses one or two contact transducers (four different probes included; 90 °, 70 °, 60 °, 45 °) to measure material or wall thickness, detect flaws or defects in welds, and monitor the effects of corrosion on pipes and tanks.

PCE-USC 20 is an ultrasonic thickness gauge used for non-destructive testing (NDT) and inspection in a wide variety of applications in industries such as chemical, oil and gas, metallurgical, manufacturing, quality control, metalworking, welding, machining, engineering, product research and development, construction, transportation and aerospace.

– Measurement range: 0.5 … 9999 mm (steel; longitudinal wave)
– Operating frequency range: 0.5 … 20 MHz
– Sound velocity: 1000 … 15000 m/s (continuously adjustable)
– AVG and DAC evaluation methods, display and probes delay, damping and reinforcing functions, export and reporting functions
– Saves up to 500 records to memory
– Lightweight design for ease of portability
– Complies with EN12668-1

Technical specifications
Measurement range	0.5 … 9999 mm (longitudinal shaft steel), continuously adjustable
Sound velocity	1000 … 15000 m/s, continuously adjustable, coarse adjustment
Display delay	-10 … 2000 mm
Probe delay	0.00 … 199.9 µs
Transmitting impulse	400 V negative signal peaks
Damping (impulse generator)	50 / 100 / 200 / 500
Work mode	One- or two-probe measurement
Operating frequency range	0.5 … 20 MHz
Pulse repetition frequency	40 / 250 /1000 Hz optional
Amplification / gain (receiver)	0 … 110 dB
Rectification (receiver)	Whole wave, positive half wave, negative half wave, high frequency representation
Alarm limits	Limit A (Gate A) and Limit B (Gate B), Adjustable as positive or negative peak with automatic (visual or audible) alarm
Measurement mode	Limit value / Extreme value mode
Measurement deviation horizontal linearity	≤0.1 %
Measurement deviation vertical linearity	≤3 %
Excess sensitivity	≥62 dB
Dynamic range	≥40 dB
Resolution remote field	≥30 dB
Sampling rate	400 MHz
Measurement data storage	500 records
Signal reproduction	Permanent recording of signals with the playback of dynamic echoes
Surface adjustment	Automatic adjustment of the error position of the angled probes
Automatic amplification	20 … 80 %, in 1 % steps
Menu language	English, Chinese
Interface	USB-A, USB-B, Ethernet
Display	5.7 ” TFT color LCD (640 x 480 pixels)
Operating temperature	-10 … +50 °C
Power supply	AC: 100 … 240 V DC: 15 V / 4 A
Battery	Li-ion battery (10.8 V, 5200 mAh)
Battery opearting time per charge	>6 hours
Protection class	IP54
Weight	1.4 kg (incl. battery)

The post Ultrasonic Thickness Gauge PCE-USC 20 appeared first on Amet Co.,Ltd.

Ultrasonic Thickness Gauge PCE-FD 20

Admin Amet — Thu, 29 Apr 2021 04:17:44 +0000

PCE-FD 20 is a portable ultrasonic tester or ultrasonic thickness gauge with a large LCD screen that displays A-scan maps of ultrasonic signals as well as B-scan cross sections. Ideal for use in mechanical engineering, aerospace and metallurgical applications, this high-frequency ultrasound-based thickness meter uses a contact transducer (two different probes included; 45° and 90°) to measure material thickness and identify flaws and defects such as discontinuity in welds.

– Operating frequency range: 1 … 10 MHz
– Measured time interval range: 6 … 1000 microseconds (µs)
– Sound velocity: 1000 … 9999 m/s
– Implements shadow, echo and mirror-shadow testing methods
– Features a USB interface for downloading data to PC for detailed analysis
– Lightweight
– Battery or electric power
– 1.5 m long probe cable

Technical specifications

Operating frequency range	1 … 10 MHz
Measure time interval range (scan duration)	6 … 1000 microseconds (µs)
Sound velocity range	1000 … 9999 m/s
Deviation of measurement of time intervals	Not exceed ± 0.025 µs
Max. deviation of amplitude of signals at receiver input in 0 … 110 dB range	Not exceed ± 0.5 dB
Testing gain region	125 dB
Averaging over the quantity of starts	1 … 16
Range of time-variable gain (TVG) / Number of control points TVG	40 dB / 15
Duration of excitation pulse to load	0 … 0.5 µs
Amplitude of excitation pulse to 50 Ohm load, not less	100, 200, 300
Operating frequency range of receiver at -3 dB	1 … 10 MHz
Deviation of amplitudes of input signals in 10 … 100% range of screen height	Not more than 1 dB
Scanning	1 … 1000 µs
Scanning delay	0 … 2000 µs
Measurement range of time intervals	0 … 1000 µs
Prism of probe delay	0 … 15 µs
Automatic signaling of defects (AFS)	Dual-gate
Setting range of AFS gates	0 … 2000 µs
Adjusting thresholds of AFS gates	0 … 100%
Detection of signals (receiver)	Positive half-wave, radio mode
Dimensions of device (approx.)	80 x 162 x 35 mm / 3.14 x 6.37 x 1.37″
Dimensions display (approx.)	48 x 74 mm / 1.88 x 2.91″
Power supply	100 … 250 V AC or 3 x 1.5 V AA batteries
Weight (approx.)	250 g / 0.55 lb (without batteries)

The post Ultrasonic Thickness Gauge PCE-FD 20 appeared first on Amet Co.,Ltd.

Thickness Gauge PCE-CT 90-ICA Incl. ISO Calibration Certificate

Admin Amet — Thu, 29 Apr 2021 04:15:38 +0000

Thickness Gauge PCE-CT 90-ICA Incl. ISO Calibration Certificate
Coating thickness gauge with various sensors / Measuring range up to 60 mm / Automatic sensor detection / Temperature, roughness, dew point, ambient humidity / Coating thickness measurement for Fe and NFe measurements / For mobile use

The coating thickness gauge is a versatile measuring instrument. This is made possible by the various optional sensors on the layer thickness gauge. For example, the coating thickness gauge can easily measure the layer thicknesses of paints, galvanic coatings, galvanizing or even anodic oxide layers on metal. With the sensors, for example, layer thickness measurements with a thickness of up to 60 mm are possible.

In addition to the layer thickness sensors for the layer thickness gauge, there is also the climate sensor. With this climate sensor at the coating thickness gauge, the ambient temperature, the ambient humidity and the dew point can be measured. Also, in the film thickness gauge, there is the surface temperature sensor. Thanks to the surface temperature sensor, the surface temperature of an object in a measuring range of -50 … 125°C / -58 … 257°F can be determined with the Coating Thickness Gauge.

In addition, the roughness of surfaces can be determined with the layer thickness gauge. This is made possible by the optional roughness meter. With the roughness sensor from the layer thickness gauge, the Rz value of the surface can be determined within a very short time. The measuring range here is between 0 … 300 μm.

– Different sensors
– Measuring range up to 60 mm
– Automatic sensor detection
– Zero point and one-point calibration
– Power supply 2 x 1.5V AAA batteries
– Temperature measurement up to 125°C / 257°F
– Incl. ISO calibration certificate

Measuring range		sensor-dependent (see sensor table)
Accuracy		sensor-dependent (see sensor table)
Measurable materials		magnetic materials (iron, steel …) non-magnetic materials (paints, plastics, ceramics, …)
Min. radius of curvature		0.3 … 50 mm / 0.012 … 1.97″ (depending on the sensor used)
Calibration		Zero calibration, one-point calibration
Units		µm, mm, °C
Power supply		2 x 1.5 V AAA batteries (DC)
Display		Graphic display
Operating conditions		-10 … 40 °C / 14 … 104 °F, 20 … 98% r. H., non-condensing at 35 °C / 95 °F
Storage conditions		5 … 40 °C / 41 … 104°F, 80% r. H., non-condensing at 25 °C / 77 °F
Dimensions		136 x 75 x 32 mm / 5.4 x 3 x 1.3″
Weight		168 g / < 1 lb

Sensor table
Model	Measuring range	Accuracy	Measurement Description
Fe-0.3*	0 … 300 µm	±(3 % + 1 µm)	Paint, lacquer, galvanic coating
Fe-0.5*	0 … 500 µm	±(3 % + 1 µm)	Paint, lacquer, galvanic coating
Fe-2*	0 … 2000 µm	±(3 % + 2 µm)	Paint, lacquer
Fe-5*	0 … 5000 µm	±(3 % + 2 µm)	Lacquer and thick coating
NFe-2**	0 … 2000 µm	±(3 % + 2 µm)	Anodic oxidelayer, lacquer layers
M12***	0 … 12 mm / 0 … 0.47″	±(3 % + 0.01 mm)	Thick coating
M30***	0 … 30 mm / 0 … 1.18″	±(3 % + 0.02 mm)	Thick coating
M60***	0 … 60 mm / 0 … 2.36″	±(3 % + 0.03 mm)	Thick coating
DT	-50 … 125°C / -58 … 257 °F	±1 °C	Surface temperature
DTVR	Temperature: -50 … 125 °C / -58 … 257 °F	±1 °C	Air temperature
	Humidity: 0 … 100 %	±5 %	Humidity
	Dew point: -15 …+40 °C / 5 … 104 °F	±2 °C	Dew point
DSH	1 … 300 µm	±(3 % + 2 µm)	Roughness


* Fe: only for ferromagnetic substrates

** NFe: only for non-ferromagnetic substrates

*** Fe und NFe: for ferromagnetic and non-ferromagnetic substrates

The post Thickness Gauge PCE-CT 90-ICA Incl. ISO Calibration Certificate appeared first on Amet Co.,Ltd.

Thickness Gauge PCE-CT 90

Admin Amet — Thu, 29 Apr 2021 04:12:37 +0000

Thickness gauge PCE-CT 90
Coating thickness gauge with various sensors / Measuring range up to 60 mm / Automatic sensor detection / Temperature, roughness, dew point, ambient humidity / Coating thickness measurement for Fe and NFe measurements / For mobile use

Measuring range		sensor-dependent (see sensor table)
Accuracy		sensor-dependent (see sensor table)
Measurable materials		magnetic materials (iron, steel …) non-magnetic materials (paints, plastics, ceramics, …)
Min. radius of curvature		0.3 … 50 mm / 0.012 … 1.97″ (depending on the sensor used)
Calibration		Zero calibration, one-point calibration
Units		µm, mm, °C
Power supply		2 x 1.5 V AAA batteries (DC)
Display		Graphic display
Operating conditions		-10 … 40 °C / 14 … 104 °F, 20 … 98% r. H., non-condensing at 35 °C / 95 °F
Storage conditions		5 … 40 °C / 41 … 104°F, 80% r. H., non-condensing at 25 °C / 77 °F
Dimensions		136 x 75 x 32 mm / 5.4 x 3 x 1.3″
Weight		168 g / < 1 lb

Sensor table
Model	Measuring range	Accuracy	Measurement Description
Fe-0.3*	0 … 300 µm	±(3 % + 1 µm)	Paint, lacquer, galvanic coating
Fe-0.5*	0 … 500 µm	±(3 % + 1 µm)	Paint, lacquer, galvanic coating
Fe-2*	0 … 2000 µm	±(3 % + 2 µm)	Paint, lacquer
Fe-5*	0 … 5000 µm	±(3 % + 2 µm)	Lacquer and thick coating
NFe-2**	0 … 2000 µm	±(3 % + 2 µm)	Anodic oxidelayer, lacquer layers
M12***	0 … 12 mm / 0 … 0.47″	±(3 % + 0.01 mm)	Thick coating
M30***	0 … 30 mm / 0 … 1.18″	±(3 % + 0.02 mm)	Thick coating
M60***	0 … 60 mm / 0 … 2.36″	±(3 % + 0.03 mm)	Thick coating
DT	-50 … 125°C / -58 … 257 °F	±1 °C	Surface temperature
DTVR	Temperature: -50 … 125 °C / -58 … 257 °F	±1 °C	Air temperature
	Humidity: 0 … 100 %	±5 %	Humidity
	Dew point: -15 …+40 °C / 5 … 104 °F	±2 °C	Dew point
DSH	1 … 300 µm	±(3 % + 2 µm)	Roughness


* Fe: only for ferromagnetic substrates

** NFe: only for non-ferromagnetic substrates

*** Fe und NFe: for ferromagnetic and non-ferromagnetic substrates

The post Thickness Gauge PCE-CT 90 appeared first on Amet Co.,Ltd.

Thickness Gauge PCE-CT 100N-ICA incl. ISO Calibration Certificate

Admin Amet — Thu, 29 Apr 2021 04:08:45 +0000

Thickness gauge PCE-CT 100N-ICA incl. ISO Calibration Certificate
Surface tester for ferrous and non-ferrous metals / Very compact size / Non-destructive, precise measurements / Data transmission via USB and Wifi / Simple operation / Uncomplicated and reliable

The surface tester works according to the magnetic inductive (ISO 2178) and the eddy current method (ISO 2360). These methods supported by the surface tester are used for the non-destructive testing of materials. The surface tester is used to measure the thickness of magnetically neutral layers on a magnetic or non-magnetic base material.

The surface tester is ideal for reliable layer thickness measurements on site. With the external probe, the layer thickness can be measured quickly and easily, even in hard-to-reach places. The surface tester was developed for non-destructive, fast and precise layer thickness measurements and is easy to use. Measured data can be easily transferred to a PC using a USB data storage device or via WiFi.

The surface tester is used in particular in the finishing industry, electroplating, ship and bridge construction, aircraft construction and the machine and chemical industry.

– Illuminated touch keyboard
– Measurement data storage for up to 500 data
– One-point and multi-point calibration
– Single measurement and continuous measurement
– Data transfer via wifi and USB
– Two different probes for NFe and Fe
– incl. ISO Calibration Certificate

Measuring range	0 … 1250 µm; 0 … 49.2 mil
Min. coating thickness of base material	50 µm
Smallest measuring surface (diameter)	10 mm
Min. radius of curvature convex	15 mm
Min. radius of curvature concave	15 mm
Accuracy	± (1% + 1 µm); ± (1% + 0.04 mil)
Resolution	0.1 µm (<99.9 µm); 0.004 mil (<3.9 mil)
	1 µm (> 100 µm); 0.04 mil (> 3.9 mil)
Calibration	Single point, multiple point
Data storage	500 data
Measuring modes	Single measurements, continuous measurement
Interfaces	Wifi , USB
Operating conditions	0 … 50°C / 32 … 122°F, 20 … 90% RH non-condensing
Dimensions	170 x 85 x 35 mm / 6.7 x 3.3 x 1.4 in
Weight	Approx. 335 g / < 1 lb (with battery)

The post Thickness Gauge PCE-CT 100N-ICA incl. ISO Calibration Certificate appeared first on Amet Co.,Ltd.

Thickness Gauge PCE-CT 100N

Admin Amet — Thu, 29 Apr 2021 04:05:50 +0000

Thickness gauge PCE-CT 100N
Surface tester for ferrous and non-ferrous metals / Very compact size / Non-destructive, precise measurements / Data transmission via USB and Wifi / Simple operation / Uncomplicated and reliable

The surface tester is used in particular in the finishing industry, electroplating, ship and bridge construction, aircraft construction and the machine and chemical industry.

Measuring range	0 … 1250 µm; 0 … 49.2 mil
Min. coating thickness of base material	50 µm
Smallest measuring surface (diameter)	10 mm
Min. radius of curvature convex	15 mm
Min. radius of curvature concave	15 mm
Accuracy	± (1% + 1 µm); ± (1% + 0.04 mil)
Resolution	0.1 µm (<99.9 µm); 0.004 mil (<3.9 mil)
	1 µm (> 100 µm); 0.04 mil (> 3.9 mil)
Calibration	Single point, multiple point
Data storage	500 data
Measuring modes	Single measurements, continuous measurement
Interfaces	Wifi , USB
Operating conditions	0 … 50°C / 32 … 122°F, 20 … 90% RH non-condensing
Dimensions	170 x 85 x 35 mm / 6.7 x 3.3 x 1.4 in
Weight	Approx. 335 g / < 1 lb (with battery)

The post Thickness Gauge PCE-CT 100N appeared first on Amet Co.,Ltd.

Thickness Gauge PCE-TG 300

Admin Amet — Thu, 29 Apr 2021 04:01:59 +0000

Thickness gauge PCE-TG 300
Large measuring range / Up to 600 mm / Pulse-echo or echo-echo mode / For all homogeneous materials / Print function via Bluetooth / USB connection

The PCE-TG 300 is a wall thickness gauge with special sensors for various applications. In general, the wall thicknesses of all homogeneous materials can be measured with the PCE-TG 300. For damping or scattering materials such as plastic or cast a special sensor is available. An angled 90° sensor also enables measurements at hard-to-reach measuring points. The speed of sound can be set freely on the wall thickness gauge PCE-TG 300 and thus adapted to a wide variety of materials.

The measured values are displayed directly on the easy-to-read TFT color display. Due to the internal memory, which can be read out via the optionally available software, different measuring points can be clearly stored. The non-destructive ultrasound measuring method enables the measurement even on end products. Thanks to the Echo-Echo working mode, even coated workpieces can be measured.

– Large measuring range
– Various sensors available
– Battery operation
– Error and voids detection
– Internal measurement data memory
– Print via Bluetooth

Measuring range	PE: pulse-echo mode 0.65 … 600 mm (steel)
	EE: echo-echo mode 2.50 … 60 mm
Accuracy	± 0.04 mm H [mm] (<10 mm); ± 0.4% H [mm] (> 10 mm)
	H refers to the material thickness of the workpiece
Resolution	0.1 mm / 0.01 mm / 0.001 mm (adjustable)

Measurable materials	Metals
	Plastics
	Ceramics
	Epoxy resin
	Glass
	And all homogeneous materials

Working modes	Pulse echo mode (fault and blower detection)
	Echo-Echo mode (hiding layer thicknesses, eg paints)

Calibration	Sound velocity calibration
	Zeroing
	Two-point calibration

View mode	Normal mode, Scan mode, Difference mode
Units	mm / inch
Data transfer	Print via Bluetooth / USB 2.0
Storage	Non-volatile memory with 100 data groups with 100 data sets each
Operating time	Continuous operation 100 h
	Automatic stand-by mode (adjustable)
	Automatic switch-off mode (adjustable)

Power supply	4 x AA battery 1.5V
Display	320 x 240 pixels TFT LCD color display with brightness adjustment
Operating conditions	0 … 50°C / 32 … 122°F, ≤ 80% RH not condensing
Storage conditions	-20 … 70°C / -4 … 158°F, ≤ 80% rh non-condensing
Dimensions	185 x 97 x 40 mm / 7.3 x 3.8 x 1.6 in
Weight	375 g / < 1 lb

Specification of the available sensors for wall thickness gauge PCE-TG 300

NO2
Frequency	2.5 MHz
Diameter	14 mm
Measuring range	3 … 40 mm (steel)
	3 … 300 mm (steel)
Minimum diameter of pipes	Not suitable for curved materials
Description	For damping / scattering materials (plastics, cast iron)

NO5
Frequency	5 MHz
Diameter	10 mm
Measuring range	1 … 600 mm (steel)
Minimum diameter of pipes	20 x 3 mm
Description	Normal measurement

NO5 / 90°
Frequency	5 MHz
Diameter	10
Measuring range	1 … 600 mm (steel)
Minimum diameter of pipes	20 x 3 mm
Description	Normal measurement

NO7
Frequency	7 MHz
Diameter	6 mm
Measuring range	0.65 … 200 mm (steel)
Minimum diameter of pipes	15 x 2 mm
Description	Or thin-walled or heavily curved pipes

HT5
Frequency	5 MHz
Diameter	12 mm
Measuring range	1 … 600 mm (steel)
Minimum diameter of pipes	30 mm
Description	For high temperatures (max 300°C / 572°F)

P5EE
Frequency	5 MHz
Diameter	10 mm
Measuring range	PE: 2 … 600 mm, EE: 2.5 … 100 mm
Minimum diameter of pipes	20 x 3 mm
Description	Normal measurement and EE test

The post Thickness Gauge PCE-TG 300 appeared first on Amet Co.,Ltd.